DMR-чип опознан по схеме: HF6853 = AUCTUS A6 (RDA8809), не SCT3258

Опознание БЕЗ разбора рации, по схеме RT4DDLT01 (Radtel v2.1): DMR-модуль «FM100B» = один чип U700 HF6853 — одночиповый DMR-SoC семейства Auctus A6 (внутри RDA8809): CPU + ВЧ-трансивер + DSP + AMBE-вокодер + аудио-кодек в одном кристалле, прошивка во внешнем SPI-flash, кварц 26 МГц. Прежняя версия «Sicomm SCT3258TD» неверна (SCT3258 — baseband-only без ВЧ; и нативный протокол другой). Скрытый ATE/CPS-интерфейс полностью реверснут (jhart99/a6tools, вендорен в research/a6tools). Даёт КОНКРЕТНУЮ починку нашей TX-проблемы: AT+GETFREQERR / AT+DMOFREQERR=N, offset=-2500+10*N, ±2500 Гц — наши ~1100 Гц внутри диапазона. Плюс DMR_ADJTXSYMDEV (девиация), FGU_AFC, DMOSETPOWER, CPS chanInfo, дамп прошивки модуля. - docs/hf6853-auctus-a6.md — идентификация + протокол + план TX-fix - tools/a6_freqfix.py — заготовка тула (probe/read/write, не запускать вслепую) - research/a6tools/ — вендоренный реверс (MIT), atcommands.md/cpecommands.md - docs/dmr-tx-recovery.md, README — путь 0 (AT+DMOFREQERR) как лучший - research/rt4ddlt01-dmr-module-sheet.png — рендер листа схемы DMR-модуля Co-Authored-By: Claude Opus 4.8 <noreply@anthropic.com> Claude-Session: https://claude.ai/code/session_01NikMGoqQWWk9wy2ww2vJAr
2026-07-24 03:10:24 +09:00
@@ -0,0 +1,120 @@
+Command | function
+---------------------|----------
+DMOCONNECT | Required before issuing other commands
+DMODISCONNECT | Ends the current session
+DMORLIC              | Returns the Device Serial Number
+DMOVERQ              | Returns Ver 1.0.0
+DMOREVDATA | No response
+BINARY | No response
+DMOGETSTARTUP | No response
+DMOGETSOFTVERSION | Returns the firmware version
+DMOGETSQSTATUS | No response
+DMOGETCURRCH | Replies with the current channel parameters +DMOGETCURRCH:0,DIG,438802000,438802000,0,0,1,2,0,0,0 or +DMOGETCURRCH:15,ANA,405000000,405000000,1,1
+DMOGETCHFREQ | Replies with the channel parameters for the given channel number AT+DMOGETCHFREQ=<channel>
+DMOGETLNAOFFS | Returns the LNA offset
+DMOGETRSSIPARAM | Returns the RSSI offset
+DMOGETCHIPID | A unique ID for the A6 processor
+DMOGETGRPADDR | Returns the DMR contact for the current channel
+DMOGETWLKTLKID | Returns the DMR radio ID of the radio
+DMORDRSSI | Returns the current receive signal strength in dBm
+DMOTESTMODE |
+DMOSETGROUP | Sets all of the frequency settings for the given channel
+DMOSETCTCDCS | Sets the CTCSS or DCS mode for the current channel AT+DMOSETCTCDCS=<mode>,<ctcDcsType>,<ctcDcsNum>,<ctcDcsInvert>
+DMOSETCTCDCSGAIN | Sets the audio gain for the CTCSS or DCS tone AT+DMOSETCTCDCSGAIN=<ctcDcsType>,<gain>
+DMOSETTAILFREQ | Sets the tail frequency(550-2000 in tenths of Hz) for the current channel AT+DMOSETTAILFREQ=<tailFreq>
+DMOAUTOPOWCONTR | Sets the automatic power control mode for the current channel AT+DMOAUTOPOWCONTR=<mode>
+DMOSETMIC | Sets the microphone gain for the current channel AT+DMOSETMIC=<gain>
+DMOSETVOLUME | Sets the volume for the current channel AT+DMOSETVOLUME=<volume>
+DMOSETVOLUMELEVEL | Sets the volume level for the current channel AT+DMOSETVOLUMELEVEL=<level>
+DMOSETVOX | Sets the VOX level for the current channel AT+DMOSETVOX=<level>
+DMOSENDDATA | ¯\\_(ツ)_/¯
+DMOSETAPC |
+DMOSETSN |
+DMORESETSN |
+DMOSETRSSIPARAM |
+DMOSETLNAOFFS |
+DMOSAVEPARAM |
+DMOERASEPARAM |
+DMOSETSMARTLO |
+DMOGETRXBER | Returns the received bit error rate
+DMOCHSWITCH | Changes the current channel AT+DMOCHSWITCH=<channel>
+DMOSETCHFREQ | Changes the channel parameters for the given channel number AT+DMOSETCHFREQ=<txfreq>,<rxfreq> where the frequencies are like this 438.8001.  Must have this number of digits to work
+DMOSETCHPOWER |
+DMOSETPOWER | Sets the power level for the current channel AT+DMOSETPOWER=<level> where level is 0-2
+DMOSETPWRSAVELV | Sets the FM power save level for the current channel if no audio, the radio will stop transmitting AT+DMOSETPWRSAVELV=<level>
+DMOSETWLKTLKID | Set the DMR Radio ID
+DMOSETGRPADDR | Set the DMR group address
+DMOSETFREQBANDNUM | Set the number of frequency bands AT+DMOSETFREQBANDNUM=<number> where number is less than 16
+DMOGETFREQBANDNUM | Get the current number of frequency bands
+DMOSETFREQBANDVAL | Set the values of the frequency bands 
+DMOGETFREQBANDVAL | Get the values of the frequency bands
+DMOAMPCTRLTEST | Sets an amplifier gain and tests the amplifier AT+DMOAMPCTRLTEST=<gain> gain is 0-128
+DMODIGPWRSAVECTRL |
+DMOSETLCHEADERCNT | Sets the number of LC headers sent AT+DMOSETLCHEADERCNT=<count>
+DMOGRPCALLREQ |
+DMOINDCALLREQ |
+DMOALLCALLREQ |
+DMOALERTCSBKREQ | Sends an alert call request to the radio AT+DMOALERTCSBKREQ=<dmrid>
+DMOCHECKCSBKREQ | Sends a check call request to the radio AT+DMOCHECKCSBKREQ=<dmrid>
+DMOALARMCSBKREQ | Sends an alarm call request to the radio AT+DMOALARMCSBKREQ=<dmrid>
+DMORESPCSBKREQ | Sends a response call request to the radio AT+DMORESPCSBKREQ=<dmrid>
+SETIMAGEREJEMODE |
+SETIMAGEREJE |
+SETEQUALIZER |
+SETCOMPANDER |
+SETSCRAMBLER |
+SETTONELIST |
+SETDTMF |
+RESTOREFACTORYSETTING | Restores the original settings.  The password for this is 778123456
+BERTEST |
+SETCOLORCODE | Set the color code for the current channel AT+SETCOLORCODE=<colorCode>
+GETGPADCVALUE | Get the current value of the GPADC channel(0-1) AT+GETGPADCVALUE=<channel>
+SETGPADCCHAN | Set the GPADC channel enable AT+SETGPADCCHAN=<channel>,<enable> channel=0,1 enable=0,1
+GETGPIOVALUE | Get the current value of the GPIO channel(0-32) AT+GETGPIOVALUE=<channel>
+SETGPIOVALUE | Set the GPIO channel value AT+SETGPIOVALUE=<channel>,<value> channel=0-32 value=0,1
+SETGPIODIR | Set the direction of the GPIO channel(0-32) AT+SETGPIODIR=<channel>,<direction> channel=0-32 direction=0,1
+GETPOWERAMPGAIN | Get the power amplifier gain values AT+GETPOWERAMPGAIN=<band> returns <band>,<digLow>,<digMed>,<digHigh>,<anaLow>,<anaMed>,<anaHigh>
+SETPOWERAMPGAIN | Sets the power amplifier gain
+GETPOWERAPCGAIN | Get the automatic power control gain values AT+GETPOWERAPCGAIN=<band> returns <band>,<digLow>,<digMed>,<digHigh>,<anaLow>,<anaMed>,<anaHigh>
+SETPOWERAPCGAIN | Sets the automatic power control gain
+SETPOWERAPCSW | Sets the automatic power control switch ?
+GETEFLTRXADJ | Returns the RX filter adjustment for a band AT+GETEFLTRXADJ=<band> where the value is <band>,<dac>,<gain>
+SETEFLTRXADJ | Sets the RX filter adjustment for a band AT+SETEFLTRXADJ=<band>,<dac>,<gain>
+DMOGETVAFC | Returns the current Automatic Frequency Correction value
+DMOSETVAFC | Sets the Automatic Frequency Correction value
+DMOPTT | Sets the PTT state for the current channel AT+DMOPTT=<state> where state is 0 for off and 1 for on
+GETFREQERR | Get the TCXO frequency error in 10s of Hz
+DMOFREQERR | Set the TCXO frequency error in 10s of Hz
+GETBANDBYFREQ | Returns the band number for the given frequency AT+GETBANDBYFREQ=<freq>
+DMOGETFREQBANDVAL | Returns the cut offs for the different frequency bands
+DMOGETFREQBANDNUM | Returns the number of frequency bands in use/defined AT+DMOGETFREQBANDNUM
+DMOSETFREQBANDNUM | Can be used to change the number of defined frequency bands AT+DMOSETFREQBANDNUM=2
+DMRSIGNATURE | Unknown command.  The signature looks something like this: AT+DMRSIGNATURE/aa,aa,aa,... with a total of 30 bytes worth of numbers Returns something that says AUTHSETKEYS
+WRITECFS | Does something similar to the DMRSIGNATURE command
+GETINCALLID | Returns the incoming call ID, <calltype>,<from>,<to> where call type is 0,1,2 corresponding to individual, group and all calls and from and to are DMR IDs
+SETALERTTONE |
+SETBATTDETRANGADC |
+SETBATTADJ |
+SETPROFILERAMPSSHIFT |
+SETPROFILERAMPSDWPOS |
+GETPROFILERAMPS |
+SETRAMPINGTABLE |
+GETAPC_FINEVALUE |
+SETAPC_FINEVALUE |
+DMR_ADJTXSYMDEV |
+DMR_GETTXSYMDEV |
+SETSTANDARD | Sets the testing standard for the radio AT+SETSTANDARD=<standard> where standard is 0-4.  Completely resets the radio's program!
+SETSQLEVEL |
+SETSQADJUST |
+SETSQMODE |
+SETTXIQGAIN |
+GETSQLEVEL |
+SETMODULE |
+SETCHANNELKNOBMODE |
+FGU_AFC_ADJ |
+FGU_AFC_GET |
+FGU_VCON_BIAS |
+FGU_VCON_BIAS_GET |
+_FGU_TUNE_GET |
+FGU_TUNE_GET |
+